What is 192.168.0.1 IP?
The IP address 192.168.0.1 is the default IP address for Netgear router admin access. The user has to initially login to access the admin page. To be able to do that, the user must locate the default IP address for their router and login. For most of the Netgear routers, the default IP addresses is either 192.168.01 or 192.168.1.1. The detailed step by step instructions are shared below using 192.168.0.1 IP address.
When should the IP 192.168.0.1 be used?
The default IP address 192.168.0.1 can be used to login to the Netgear router admin page. The IP 192.168.0.1 is usually the default IP address for most of the netgear routers. It may be used to personalize the network settings, gain access to numerous features that help our daily lives and more. Netgear has released a url now that helps reroute the user to the default IP addressess. But the user can simply enter either 192.168.0.1 or 192.168.1.1 in the address bar of the browser. That will take the user to the admin login page. Read below to find the step by step instructions from here on.
Steps to setup and login the Netgear router with 192.168.0.1 are as follows:
- Firstly, connect one of the Ethernet cables to the internet port of the router and the other end to the modem. Now, connect the desktop computer or laptop to the LAN port of the Netgear router using another Ethernet cable.
- Turn off the router, the modem and the computer. Turn on all the three devices after a couple of seconds and wait for all the devices to finish booting up.
- Then, open any internet browser and type 192.168.0.1 or 192.168.1.1 in the address bar. Once the user presses enter, the router admin login window will display.
This is where the user had to enter the default IP addresses for their routers which used to be 192.168.1.1 or 192.168.0.1. This has now been changed to www.routerlogin.net or www.routerlogin.com to make it easier on the user. Now, the user does not have to go around finding the default IP addresses (192.168.0.1 or 192.168.1.1) and can simply type the aforementioned addresses to gain the router’s admin login page.

- Then, enter the default information when prompted. The default username should be “admin” and password should be “password” for most of the Netgear routers. The username and password will always be case sensitive.
- If the username and password is not being accepted by the Smart Wizard (Netgear admin login page), there is a chance that the user might have changed the username and password before. In that case, the user will either have to try any previously set passwords or reset the router. The steps to reset Netgear router will be provided later in this blog.
- Once the user has successfully setup the Netgear router and logged in successfully, the Setup Wizard will appear. Click the Setup Wizard option for the screen to display. Click Yes and proceed.
- Then the Setup Wizard will display the type of IP that it will detect. The default IP address is Dynamic IP for majority of the routers.
- Lastly, if the user wishes to check the internet status, select Router Status under Maintenance.
Once the router has been setup and logged in successfully using 192.168.0.1, the user can now start configuring their router as they desire. If the user is not able to login using 192.168.0.1 or 192.168.1.1, read this to find more information.
How to reset Netgear router? (Troubleshooting steps to reset Netgear router)
If the user wishes to reset the Netgear router, simply follow the troubleshooting steps to restore the router to its factory default settings. The user can then simply go to either 192.168.0.1 or 192.168.1.1 to personalize their router by changing the settings to their needs easily.
- Locate the reset button on the Netgear router. The reset button is mostly present at the bottom of the router for most of the Netgear routers.
- Since the reset button is present inside a very small hole, locate a paper clip to press the button. Press the reset button and hold it down for about 10 seconds. The LED lights at the front of the router will start blinking.
- Once the LED light settles and becomes green/white in color, the Netgear router is restored back to its factory default settings successfully.
To know the steps to setup and login to the Netgear router, kindly refer to How to setup Netgear router? ( enter hyperlink here)
How to change the username and password for Netgear router using 192.168.0.1? Netgear username and password change troubleshooting steps:
When the user initially buys the Netgear router, the default username and password are setup to make it easy for the user to login to the router. This is because when the user uses 192.168.0.1 or 192.168.1.1 to gain access to their router settings, the user can simply enter the default username and password to easily gain access without any problems. But for the obvious reasons, the user should change the username and password to better their security against unwanted visitors using either 192.168.0.1 or 192.168.1.1.
Here are the troubleshooting steps to change the default username and password for Netgear router.
- Launch an internet browser from your internet browser and type in 192.168.0.1 or 192.168.1.1 in the address bar.
- Once the user successfully logs in to the router using either 192.168.0.1 or 192.168.1.1, a pop up window will display asking the user for the default username and password.
If the user is unable to gain access to their Netgear router’s admin login page, kindly refer to the Troubleshooting steps to Reset Netgear router mentioned above. - After successfully logging in to the router, the Basic Home page will display.

- Select the ADVANCED option.
- Click the Administration option. Then, click the Set Password option to change the login credentials of the Netgear router.
- If the user is setting up the username and password for the first time, type in the old username and password once. Then, type in the new password twice.
If the user has changed the password once before, follow the same steps using either 192.168.0.1 or 192.168.1.1 but make sure that you type in the same password you used before otherwise the user will have to reset the router again. - Make sure to enable the Enable Password Recovery option to make sure that if the user ever forgets the old password, recovery is a viable option.
- Click “Apply” to save the changes.
How to update the firmware of the Netgear router? (Troubleshooting steps to update the firmware of the Netgear router)
Netgear releases firmware updates regularly in order to ensure that the router stays up to date. The user can check th version ofthe firmware with the admin window. If you visit 192.168.0.1 or 192.168.1.1, you might see a message being displayed at the top of the screen informing the user to update the firmware of the router.
Steps to update the firmware of the Netgear router using 192.168.0.1:
- Firstly, open any internet browser that is connected to the internet. It is recommended that the router is connected to the device using an Ethernet cable to ensure that there is no chance for corruption.
- In the address bar of the internet browser, type 192.168.0.1 or 192.168.1.1 and press enter. The router’s admin login window will display.
- In the prompted screen, enter the default username and password. The default username is admin and the password is password for most of the Netgear routers. The username and password will be case sensitive.

- Once the admin login page appears, click the ADVANCED option. Then, select the Administration or Settings option. This option may vary for different router models.
- Then, select the Firmware Update or Router Update option.
- After that, click the Check option. The router will then search for any pending router firmware updates.
- If a firmware update is available, click Yes. The firmware will then update.
Take note that once the router starts updating its firmware, it should not be removed from its power source. Also, do not cancel the firmware update while its updating as it might corrupt the firmware.
The router will restart itself once the firmware update finishes. The whole process usually takes only 3-5 minutes to complete. Once the firmware has been updated, the user can login again using either 192.168.0.1 or 192.168.1.1 to check the status of the udpate.
Warning:
Do not interrupt the firmware update process as it may damage the firmware of the router and may even render the router useless. For example, do not close the browser window or turn off the device. It might damage the router and might even corrupt the firmware of the Netgear router. The user can check the status of their firmware update by logging in using either 192.168.0.1 or 192.168.1.1 IP address.
Read more about setting up your router or find the issues youre facing along with their solutions here.